ECOA TSL-60-120 Triple Scissors Lift Table

Specifications

Model	Travel	Capacity	Height		Platform Size		Base Frame	Edge Loads*		Lift Speed	Cylinders	Motor	Ship Weight*
Model	Travel	Capacity	MIN	MAX	STD	MAX	Base Frame	Static	Rolling	Lift Speed	Cylinders	Motor	Ship Weight*
TSL-60-120	120"	6,000 lbs	21.25"	141.25"	30" x 60"	48" x 84"	30" x 60"	3,000 lbs	2,000 lbs	80 sec	2	3 HP	3,000 lbs

*Note: Standard platforms only.

Oversized platforms, beveled toeguards, roller shades, accordion skirting and electrical tape switches will affect overall size. Power requirements depend upon frequency and type of operation and require specific selection. 1.5HP Power Units are internal as standard equipment. 3HP and 4.8HP Power Units are remote as standard equipment. Standard power supply for 1.5HP Power Unit is 230V/1PH/60Hz. Optional power supply for 1.5HP Power Unit is 208/230/460/3PH/60Hz. 115V/1PH/60Hz. Power Supply requires a 20 amp circuit. Standard power supply required for 3 and 4.8HP is 230/460/3PH/60Hz. Optional power supply for 3 and 4.8HP Power Units is 230/1PH/60 Hz (increases upspeed by 33%).

Note: Where available power supply is 208V/3PH, booster transformers are required for 240V/3PH for 3HP and 4.8HP motors, see options. Conforms to or exceeds ANSI standard MH29.1-1994.

Features

Smooth steel tops
On 4.8HP units, manifold with check valve, relief valve, pressure-compensated flow control valve, solenoid valve, suction and return filters. On 1.5HP or 3HP power units, valves are internally mounted on gear pump
NEMA-4X constant-pressure (water-tight, dust-tight and corrosion-resistant) "UP-DOWN" push button control station with 20 ft. coil cord
NEMA-12 prewired controls (dust/drip-tight industrial type) with liquid-tight electrical connectors. Control box contains magnetic starter, control transformer, thermal overload and fuses
Internally-mounted 1.5HP, 230V, 1PH, 60Hz TENV intermittent duty super torque motor or externally-mounted 3 or 4.8HP, 230/460V, 3PH, 60Hz continuous duty motor
Hydraulic flow limiter valve at the base of each cylinder

High-pressure gear pump
Optional upper travel limit switch
Hard, chrome-plated, polished shafting, hydraulic cylinder piston rods and axles
Lifetime self-lubricating, PTFE lined, composite bearings at all pivot points
10 ft. power cord, connector not included (For internal power unit only)
Safety restraint maintenance bars
All controller components are UL and/or CSA approved
Straight toeguards with yellow and black safety stripes
24V operating control voltage
Mechanical upper travel stops

Options

Please Note: Only common options are listed in the quote requests. If you would like additional options from the below list quoted, please include that information in the requirements section of the quote request.

Electrical Options:

Up-Down Push Button Station
Push Button mounted on platform with Disconnect Plug
Key Operated Up-Down Selector
Up-Down Push Button with Key Lockout
Foot Operated Control
Limit Switch
Booster Transformers (2 required for 3PH Power Supply)
Flashing Red Light
Two Second Up-down Warning Bell with Volume Control
Electric Toeguards, Tapeswitch
Momentary contact controls for automatic up and down operation with upper and lower limit switches and Up-Down-Stop Push Button Control Station
Photo Electric Cell Leveling (Unstacking/Stacking-Specify, 1 Direction Only)
Whisker Switch Leveling (Unstacking/Stacking-Specify, 1 Direction Only)

Hydraulic Options:

Manual Down Valve
Adjustable Flow Control Down Valve
Larger Power Unit for faster lift speeds
Remote Power Units with 5'0" hydraulic hose
Three Phase Power Unit (.75HP or 1.5HP) and Linestarter, Transformer
Air Operated Power Unit Complete 95 psi @ 60 cfm (1 HP)
External, Heavy-Duty, Continuous Running Motor Power Unit with Integral Directional Valving & Large Capacity Reservoir
Explosion Proof Power Unit-External
Quick Disconnect Couplings

Mechanical Options:

Steel Approach Ramp
Steel 42" high Handrail with Midrail/Toeboard
Roll-Up Skirting
Accordion Bellows Skirts
Straight Toeguards for surface mounting
Beveled Toeguards for pit mounting
Safety Treadplate
USDA accepted epoxy coatings for Lift Platform
Stainless Steel Platform Overlay
Ball Transfer Top
Conveyor Tops
Integrally Mounted Floor Lock

Literature

ECOA TSL Product Literature (PDF 1.0MB)

Name:		Country:		State/Prov:		Zip:
Company:		Email:		Phone:		Ext:

ECOA TSL-60-120

ECOA TSL-60-120 Triple Scissors Hydraulic Lift Table