ECOA SLD-180-710 High Capacity Loading Dock Lift

Specifications

Model	Travel	Capacity	Height		Platform Size	Base Frame	Axle Load Max		Up Speed (F.P.M.)	Motor Std. HP	Cylinders	Ship Weight
Model	Travel	Capacity	MIN	MAX	Platform Size	Base Frame	Ends	Sides	Up Speed (F.P.M.)	Motor Std. HP	Cylinders	Ship Weight
SLD-180-710	60"	18,000 lbs	18"	78"	84" x 120"	63" x 112"	14,900 lbs	12,800 lbs	7.5	5 HP	2	7,350 lbs

In 48" travel, other platform sizes are available. Listed ship weights are for standard platforms only. When voltage is 230V/1PH/60Hz lift speeds will be reduced by 33%. Note: Where available power supply is 208V/3PH booster transformers are required for 240V/3PH at motor, see options. Roller shades, accordion skirting and electrical tape switches will require a minimum lowered height of 10". Power requirements depend upon frequency and type of operation and require specific selection. 8'0" wide units require shipment via flatbed.

Features

Sealed ram-type, full oil displacement hydraulic cylinders with hard chrome plated and polished stress-proof steel rams and polyurethane seals. Positive internal stops
Safety velocity fuse at base of each cylinder to prevent descent in the event of loss of hydraulic pressure
NEMA 4, 13 (water tight, oil tight and dust tight) adjustable upper travel limit switch automatically shuts off the motor and pump at the raised-height setting
Four secondary mechanical upper travel back-up stops, 2 mounted on platform understructure and 2 mounted on base, restrict the scissor arms from moving beyond the preset travel
Axles and shafts are stressproof shafting, hard chrome plated and polished, retained with a positive-locking screw ring system and equipped with lifetime lubricated bearings
All axle and roller bearings are PTFE lined, composite type and have the qualities of good wear resistance and heat conductivity, high strength, low thermal resistance and low friction
Hydraulic hose, SAE 100 R2AT, double wire braid from cylinders to universal connection on base frame. Hose from lift to power unit is not included
Aluminum valve block manifold contains check valve, relief valve, pressure-compensated flow control valve and solenoid valve. The solenoid valve includes a filter screen
NEMA-12 prewired control box (dust/drip-tight industrial type) with liquid-tight electrical connectors. Control box contains magnetic starter, control transformer, thermal overload and fuses, mounted on the oil reservoir
High-pressure gear pump

Safety tread steel plate platform with 8 in. beveled toeguards and black and yellow safety stripes
Steel safety tread bridge plate, 18 x 72 in., with 2 safety chains
Two removable steel handrails 42 in. high with midrail
Four safety chains with snap hooks
Rectangular, structural tube scissor legs and torque tubes
Positive stops on all four corners for maximum roll-over capacity in lowered position
Hinged safety restraint maintenance bars
Surfaces degreased, oxide primed and finished with two coats of enamel
External power unit is prewired, factory tested and assembled
5HP or 7.5HP, 230/460V, 3PH, 60Hz continuous duty TEFC motor
11 gal. reservoir, oil not included
Pressure line 25-micron cartridge filter
Liquid tight strain relief type electrical cord connectors
NEMA-4X constant-pressure (water-tight, dust-tight and corrosion-resistant) "UP-DOWN" pushbutton control with 20 ft. coiled cord and hanger bracket
24V operating control voltage
All controller components are UL and/or CSA approved

Options

Please Note: Only common options are listed in the quote requests. If you would like additional options from the below list quoted, please include that information in the requirements section of the quote request.

Electrical Options:

Up-Down Push Button Station
Push Button mounted on platform with Disconnect Plug
Key Operated Up-Down Selector
Up-Down Push Button with Key Lockout
Foot Operated Control
Limit Switch
Booster Transformers (2 required for 3PH Power Supply)
Two Second Up-down Warning Bell with Volume Control
Electric Toeguards, Tapeswitch
Control Coil Cord
Oil Reservoir Immersion Heater with Thermostat Control

Hydraulic Options:

Manual Down Valve
Adjustable Flow Control Down Valve
Weather Resistance Power Unit Cover
Larger Power Unit for faster lift speeds
Hoses with End Fittings
Quick Disconnect Couplings

Mechanical Options:

Steel Safety Treadplate Bridge Plate with Hinge Assembly
Alumnimum Treadplate Throwover Bridge with Hinge Assembly
Fully Automatic Mechanical Wheel Chock
Approach Ramps (Steel Treadplate)
Handrails
Toeboards
Roll-Up Safety Skirting
Accordion Bellows Skirts

Postal Options, USPS Specifications:

Flashing red light
Warning bell with volume control
Manual down valve
Upper travel limit siwtch
36" x 66" aluminum bridge plate
Wall mounting brackers for power unit
In-line filters
12 f.p.m min. up speed
Special post office safety yellow paint
Meets USPS master spec V5.04.1 section 11163

Power Unit Assembly:

5HP 230V/1PH/60Hz Power Unit Assembly
Wall Mounting Brackets
Explosion Proof Power Unit
Flashing red light

Literature

ECOA SLD Product Literature (PDF 89KB)

Name:		Country:		State/Prov:		Zip:
Company:		Email:		Phone:		Ext:

ECOA SLD-180-710

ECOA SizzrDok SLD-180-710 Loading Dock Lift