ECOA DSL-20-120 Double Scissors Lift Table

Specifications

Model	Travel	Capacity	Height		Platform Size		Base Frame	Edge Loads*		Lift Speed	Cylinders	Motor	Ship Weight
Model	Travel	Capacity	MIN	MAX	STD	MAX	Base Frame	Static	Rolling	Lift Speed	Cylinders	Motor	Ship Weight
DSL-20-120	120"	2,000 lbs	14"	134"	54" x 96"	72" x 120"	54" x 96"	1,000 lbs	670 lbs	30 sec	2	4.8 HP	3,400 lbs

*Note: Standard platforms only.

Oversized platforms, beveled toeguards, roller shades, accordion skirting and electrical tape switches will affect overall size. Power requirements depend upon frequency and type of operation and require specific selection. Standard power supply for .75 and 1.5HP power Unit is 230V/1PH/60hz. Optional power supply for .75 and 1.15HP Power Unit is 208/230/460/3PH/60Hz . Standard power supply for 4.8HP power units is 230/460/3PH/60Hz. Optional power supply for 4.8HP power unit is 230V/1PH/60Hz (increases upspeed by 33%).

Note: Where available power supply is 208V/3PH, booster transformers are required for 240V/3PH at motor, see options. Conforms to or exceeds ANSI standard MH29.1-1994.

Features

Straight toeguards with yellow and black safety stripes
Internally-mounted 1.5HP, 230V, 1PH, 60Hz TENV intermittent duty super torque motor or externally-mounted 4.8HP, 230/460V, 3PH, 60Hz continuous duty motor
On 4.8HP units, manifold with check valve, relief valve, pressure-compensated flow control valve, solenoid valve, suction and return filters. On 1.5HP power units, valves are internally mounted on gear pump
NEMA-4X constant-pressure (water-tight, dust-tight and corrosion-resistant) "UP-DOWN" pushbutton control station with 20 ft. coil cord
NEMA-12 prewired controls (dust/drip-tight industrial type) with liquid-tight electrical connectors. Control box contains magnetic starter, control transformer, thermal overload and fuses
All controller components are UL and/or CSA approved

High-pressure gear pump
24V operating control voltage
Hydraulic flow limiter valve at the base of each cylinder
Optional upper travel limit switch
Hard, chrome-plated, polished shafting, hydraulic cylinder piston rods and axles
Lifetime self-lubricating, PTFE lined, composite bearings at all pivot points
Mechanical upper travel stops
Smooth steel tops

Options

Please Note: Only common options are listed in the quote requests. If you would like additional options from the below list quoted, please include that information in the requirements section of the quote request.

Electrical Options:

Up-Down Push Button Station
Push Button mounted on platform with Disconnect Plug
Key Operated Up-Down Selector
Up-Down Push Button with Key Lockout
Foot Operated Control
Limit Switch
Booster Transformers (2 required for 3PH Power Supply)
Flashing Red Light
Two Second Up-down Warning Bell with Volume Control
Electric Toeguards, Tapeswitch
Momentary contact controls for automatic up and down operation with upper and lower limit switches and Up-Down-Stop Push Button Control Station
Photo Electric Cell Leveling (Unstacking/Stacking-Specify, 1 Direction Only)
Whisker Switch Leveling (Unstacking/Stacking-Specify, 1 Direction Only)

Hydraulic Options:

Manual Down Valve
Adjustable Flow Control Down Valve
Larger Power Unit for faster lift speeds
Remote Power Units with 5'0" hydraulic hose
Three Phase Power Unit (.75HP or 1.5HP) and Linestarter, Transformer
Air Operated Power Unit Complete 95 psi @ 60 cfm (1 HP)
External, Heavy-Duty, Continuous Running Motor Power Unit with Integral Directional Valving & Large Capacity Reservoir
Explosion Proof Power Unit-External
Quick Disconnect Couplings

Mechanical Options:

Steel Approach Ramp
Steel 42" high Handrail with Midrail/Toeboard
Roll-Up Skirting
Accordion Bellows Skirts
Straight Toeguards for surface mounting
Beveled Toeguards for pit mounting
Safety Treadplate
USDA accepted epoxy coatings for Lift Platform
Stainless Steel Platform Overlay
Ball Transfer Top
Conveyor Tops
Integrally Mounted Floor Lock

Literature

ECOA DSL Product Literature (PDF 604KB)

Name:		Country:		State/Prov:		Zip:
Company:		Email:		Phone:		Ext:

ECOA DSL-20-120

ECOA DSL-20-120 Double Scissors Hydraulic Lift Table