American Lifts PT-45-060 TiltLift by Autoquip

Specifications

TiltLift Specifications
Model	Travel	Capacity	Tilt	Height		Platform Size			Base Frame	Speed		Cylinders	Motor	Weight	Quote Form
Model	Travel	Capacity	Tilt	MIN	MAX	MIN	STD	MAX	Base Frame	Up	Down	Cylinders	Motor	Weight	Quote Form
PT-45-060	25"	6,000 lbs	45°	8"	33"	24" x 36"	24" x 48"	48" x 48"	23" x 34.63"	40 sec	10 sec	1	1 HP	850 lbs

Features

All scissors rollers are captured within structural steel channels to provide excellent load stability.
High impact, spiral wound bearings at every pivot point provide maintenance-free, rugged resistance to abrasion, impact, and uneven loads.
Structural cross-members at every pinned joint in the scissors assembly minimizes leg deflection.
All hydraulic cylinders contain two-piece, self-aligning piston rods that transmit minimal side forces to the cylinder hinges/pins.
Structural steel channels in all top and lower frames provide additional rigidity and resistance to twisting/bending of the lift under load.
Solid steel legs and added stiffeners provide overall stability and straight, repeatable roller tracking as the lift raises and lowers.
Joints feature chrome-plated, 100,000 psi, ultimate-strength pins for premium load strength and long life.
Minimum 1/4-inch-thick steel-reinforced platform minimizes deck deflection and maximizes load stability.
Autoquip offers an industry-best 2 year warranty on all parts as a promise that you've purchased the industry's most reliable scissor lift.
On-board maintenance devices enable maintenance crews to safely and effectively block open the scissors during inspection.
Semi-transparent poly oil reservoir provides an easily visible method of checking fluid levels and eliminates oil contamination due to rust.
Low pressure hydraulic circuit extends the life of all hydraulic components and puts less stress on the electric motor.
Double wire braided Parker hydraulic hoses resist wear, abrasion, and leaks.
TiltLift's extremely small footprint allows workers to stand close to the product, which minimizes reaching.
Non-intrusive design minimizes floor space requirements for the operator
Extremely low collapsed height increases its total ergonomic range.
Standard controls are prewired and internal power unit is onboard.
Designed to handle load centering over the structural base frame while raising and lowering.
Hydraulic velocity fuses completely stop lifts in the unlikely event of uncontrolled descent due to sudden hose rupture.
Minimum 3:1 structural factor of safety makes these lifts the most structurally sound lift in the industry.
Compliance with recognized standards:
- ANSI MH29.1 - Safety Requirements for Industrial Scissor Lifts
- NFPA 70 - National Electric Code
- ASTM - A36 - Structural Steel Standard
- ANSI Z535 - Safety Labeling Requirements
- AWS D.1 - Welding Standards
- Applicable portions of OSHA 29CFR1910 - General workplace safety

Options

Please Note: Only common options are listed in the quote requests. If you would like additional options from the below list quoted, please include that information in the requirements section of the quote request.

Power Unit Options:

Cover for Remote Power Unit
Int. 3/4 HP Single Phase Power Unit
Hydraulic Hose Quick Disconnect
Remote Air Operated Power Unit
Hand Operated Up/Down Control
Foot Operated Up/Down Air Valve
Water Glycol
Food Grade Oil
Biodegradable Oil
Manual Valve Off Pressure Line
Connection Hose
3HP 3 Phase Pump Unit
5HP 3 Phase Pump Unit
Air Powered Hydraulic Pump
Continuous Running Pump Unit
External Pump Unit
Teledyne Hand Pump
Washdown (NEMA 4) Pump Unit
No Power Unit & No Controls

Electrical Options:

Guarded Up/Down Foot Switch
Upper/Lower Travel Limit Switch
Key Lockout Switch
115 Volt Controls
NEMA-12 Enclosure
115 Volt AC Down Solenoid Coil
24 Volt DC Down Solenoid Coil
Magnetic Push Button Station
Up/Down Push Button Station
Hook for Pushbutton
Weatherproof Push Button
Audible Signal w/Volume Adjust
Flashing Red Light
No Controls

Baseframe Accessories:

Anchor Clips
Built Up Baseframe
Fork Truck Pockets

Platform Options:

Larger Platform Sizes

Gates & Enclosures

Single Swing Gates
Biparting Swing Gates
Single Panel Vertical Acting Gates
Bi Panel Vertical Acting Gates
Horizontal Sliding Gates
Panels (standard 96" high)
Interlocks

Paint Options:

Black, Brown, Machinery Grey, Blue
Match Color
Safety Colors: Orange or Yellow
Epoxy Paint
Steel-it
Primer Only
Tile Clad Epoxy

Literature

Autoquip TiltLift Product Literature (PDF 840Kb)

Name:		Country:		State/Prov:		Zip:
Company:		Email:		Phone:		Ext:

Autoquip PT-45-060

American Lifts PT-45-060 TiltLift by Autoquip